Oil Flow Control Supply Pump and the Burner Assembly

Oil Flow Control Supply Pump and Burner Assembly

Our patented complete waste oil burning system with a universal burner mounting flange allows easy retrofit of our burner system to various configuration and sizes of combustion chambers. Initial flame adjustment is all that is needed with complete control thereafter.

OMNI is the only waste oil burner manufacturer who can say without equivocation it's oil preheater block absolutely will not carbon the oil internally due to its patented design. Therefore, the industry normal removal of carbon in the preheater block is not necessary. This design ensures that OMNI customers will never need to remove the burner for periodic carbon cleaning!

There are many who have easy access to their oil preheater block, but cleaning the hard lava-like carbon is not an easy task! Others request the entire burner be serviced at least annually. Part of that service is flushing their oil preheater block of carbon buildup. Some must do this more than others, as frequently as twice a season.

Fully cleaning and removing carbon is a difficult chore. Even after cleaning, carbon chunk particles can remain. Shortly after service, they can plug the oil nozzle, shutting the unit down. This causes a lot of down time and repeat service, not experienced with OMNI units.

Additionally, some manufacturers request their customers shut the unit down during the summer months to eliminate the carboning process. This is not necessary if the heater block assembly is Econo Heat's OMNI system. Just leave your unit on and it will automatically start by the thermostat when heat is needed. OMNI burners do no need to be torn apart to access the heater block for cleaning. These are a few of the operating procedures COMPETITORS believes are standard; NOT WITH OMNI!

Variably controlled, A/C converted, D/C gear motor driven waste oil pump. This Remote flow control pump supplies the exact gallons of oil per hour to each waste oil burning appliance, regardless of viscosity. This pump is to be located at oil supply tank and is capable of pushing 100's of feet to the used oil firing unit.

Continues the stabilization of the waste oil viscosity by holding oil and air temperatures that pass through it exact. Resulting in the most thorough and complete burn. OIL HEATER BLOCK WILL NOT BUILD UP CARBON INSIDE ITS OIL PASSAGES!

Benefits of Burning with
Waste Oil Burners

MEETS EPA REGULATIONS
BURNS CLEAN - ZERO SMOKE
ABSOLUTELY WILL NOT CARBON

Omni Waste Oil Burner

Unparalleled Standard Features lead to Unequaled Performance

Burns Clean – Zero Smoke.
Burns clean with zero smoke, when U.L. tested we saw between 0-1 on a Bacharach scale of 0-10, cleaner burning than some standard oil burners.

Flame Control System

The OMNI Flame Control System is a patented system that consists of an Oil Flow Supply Pump and a Non-Carboning Oil Preheater that controls the fuel by volume.
No Adjustments needed for various viscosities.

The Flame Control System can be purchased separately with a universal burner mounting flange allows easy retrofit of our burner system to various configuration and sizes of combustion chambers. Initial flame adjustment is all that is needed with complete control thereafter.

Flame Control System Benefits:

Non-carboning oil heater block – cleaning not required
A thorough burn – greatly reducing ash deposit accumulation
Only system that can burn 90 weight oils
Less stress on metals – cannot over fire (after initial proper flame adjustment).
No target burn-out
The most reliable and consistent operation
Greater efficiency

Single Burner Does it All!
This model Omni burner is uniquely able to be adapted to any existing oil burning appliance without additional remote equipment needed. We accomplish this by incorporating every component required to make a waste oil burner function by integrating them into one neat package. No other manufacturer can accomplish this! Additionally this burner has a universal mounting flange for readily adaptable installation.

Built-in air compressor. Omni includes a built-in vane oil-less compressor as standard equipment. Our compressor requires no maintenance and allows the unit to be operated 24 hours/day without an external air supply.

Swing out burner door, no fuel or air lines to disconnect. Removal of one nut and electrical safety plug allows easy access to flame end cone and nozzle for quick service.

Easy Access to Burner Components.

Hinged Cover opening provides quick access to heater block and circuit board if needed.

The Industry's ONLY Non-Carboning Oil Preheater Block with a
Solid State Circuit Board Controller

These items precisely control the oil and air temperatures to insure stable viscosity for optimum control of the flame resulting in a thorough burn. Heater block never carbons or needs to be removed for cleaning. Industry normal annual parts kit not needed with OMNI's system! Readjustment of electrodes and nozzle replacement every 5 years is all that is needed due to erosion only.

These charts demonstrate the efficiency and
consistency of the Flame Control System.

Other Waste Oil Burners:

OMNI Waste Oil Burners with Flame Control:

Return to Top of Page

Vehicle Lifts

Wheel Service

Autobody

HVAC

Exhaust Benders

Pipe Benders

Vehicle Systems

Small Shop Equipment

Air Compressors

Zinko Jacks

Omni Waste Oil Burner

Unparalleled Standard Features lead to Unequaled Performance

These charts demonstrate the efficiency and
consistency of the Flame Control System.

OMNI Waste Oil Burners with Flame Control:

Omni Waste Oil Burner

Unparalleled Standard Features lead to Unequaled Performance

These charts demonstrate the efficiency and consistency of the Flame Control System.

OMNI Waste Oil Burners with Flame Control:

These charts demonstrate the efficiency and
consistency of the Flame Control System.