Axle Engaging, High & Low Pressure Variable
Wheelbase Lifts

Fully electrical/ hydraulic pump operated system which is able to lift vehicles of varying sizes. (trucks, buses, R/V's etc.). With our two differing model types of either a two or three post adjustable lifts you can easily size up the pick up points to adjust to each axle. The adjustable post(s) will make, your shop more versatile.

With adjustable support saddles on each superstructure on each post you can lift on most any axle type. With no obstructions around the lift you are ablt to reach everything quickly and easily and get the vehicles back on the road quickly and efficiently.

All operating control valves are of the dead-man type, returning to the closed position when released. The standard location for controls is at floor level to the right side (passenger side) to allow the operator to visually check positioning of the superstructures and adaptors to the contact points of the vehicle to be raised. Wall-mounted controls and control console are available as optional extras.

They're fast, simple and completely reliable. Standard movement is made with a simple chain and ratchet assembly under the floor plate. Simple control over where you want the movable post to be. Available in the following drive types:

1. "Z" hydraulic motor chain drive

2. "ZA" air motor chain drive

Supplied, capable of sustaining the lifting capacity of each post and are available in Multiposition leg only "X" Automatic latch engagement at 3 inch increments over the full rise of the piston. Disengagement for lowering is controlled by pneumatic push-button valve at the control box or electric push button on a pendant control.

Are designed to pick up most buses and trucks. Special adaptors can be supplied to suit customers' requirements.

The standard range of adjustment is 102" (2951 mm), additional range available in equal increments of 12" (305 mm)

Equipment supplied is the front pit frame, (centre pit frame if ordered) rear pit form and control box frames with covers, cylinder assemblies with hard chrome-plated piston and corrosion protected casings,locking legs, flexible front hose, control valves, oil reservoir with electric power unit.

• Remote control console

• Wall-mounted controls

• Recessed front superstructure (one opening)

• Retractable sliding covers

• Locking legs

• Power spotting

Can be supplied to operate one to five lifts. Power units consist of one or more positive displacement pumps coupled to one or more electric motors with suction filter, relief valve and pressure gauge all factory mounted on an oil reservoir of sufficient G.P.M., PSI and capacity to raise the lifts.

Stackable height adapters give a heavy duty inground unit the versatility to pick up passenger cars and light trucks. They come in several different heights and can be mixed and matched to fit the appropriate application.

PKS HAS TAKEN THE NEXT STEP FORWARD TO BRING YOU OUR ENVIRONMENTALLY FRIENDLY HIGH PRESSURE LIFTS

(complete with standard and optional features we have always offered in the low pressure units)

STANDARD FEATURES

Multiposition locking leg
Air driven adjustment allows front post positioning for various wheelbase
Auto-parking home position
Dual pendant control for easy spotting by one man
Chrome pistons both structural and high pressure
Power unit high pressure, low volume
PLC control panels

OPTIONAL

Shutter plate trench covers
In pit power unit complete with explosion proof motor
Recessed front post
Stroke limiter
Fiberglass coating on piston casings
Continuous pit

MCZC210LPEQ
(50,000lbs Capacity)
- 10 5/8" front movable post. (25K Capacity)
- 10 5/8" Rear fixed and recessed post. (25K Capacity)
- Adjustable pick up adapters
- Double chain hydraulic spotting system
- 3/8" Thick cover plates
- Locking leg with automatic air latch system
- Front frame made from 7/8" thick mast channel.
- Chrome plated pistons
- Fibreglass coated cylinder casings
- Low profile saddle

MCZC28-210LPEQ
(56,000lbs Capacity)
- 10 5/8" front movable post. (28K Capacity)
- 10 5/8" Rear fixed and recessed post. (28K Capacity)
- Adjustable pick up adapters
- Double chain hydraulic spotting system
- 3/8" Thick cover plates
- Locking leg with automatic air latch system
- Front frame made from 7/8" thick mast channel.
- Chrome plated pistons
- Fibreglass coated cylinder casings
- Low profile saddle

2MCZC310LPEQ
(75,000 lbs Capacity)
- Two 10 5/8" movable posts (25K Capacity ea.)
- One 10 5/8" fixed and recessed post. (25K Capacity)
- Adjustable pick up adapters
- Double chain hydraulic spotting system
- 3/8" Thick cover plates
- Locking leg with automatic air latch system
- Front frame made from 7/8" thick mast channel.
- Chrome plated pistons
- Fibreglass coated cylinder casings
- Low profile saddle

2MCZC28-310LPEQ
(84,000 lbs Capacity)
- Two 10 5/8" movable posts (28K Capacity ea.)
- One 10 5/8" fixed and recessed post. (28K Capacity)
- Adjustable pick up adapters
- Double chain hydraulic spotting system
- 3/8" Thick cover plates
- Locking leg with automatic air latch system
- Front frame made from 7/8" thick mast channel.
- Chrome plated pistons
- Fibreglass coated cylinder casings
- Low profile saddle

MCZC1012LPEQ
(60,000 lbs Capacity)
- One 10 5/8" movable posts (25K Capacity)
- One 12 5/8" fixed and recessed post. (35K Capacity)
- Adjustable pick up adapters
- Double chain hydraulic spotting system
- 3/8" Thick cover plates
- Locking leg with automatic air latch system
- Front frame made from 7/8" thick mast channel.
- Chrome plated pistons
- Fibreglass coated cylinder casings
- Low profile saddle

MCZC212LPEQ
(70,000 lbs Capacity)
- One 12 5/8" movable posts (35K Capacity)
- One 12 5/8" fixed and recessed post. (35K Capacity)
- Adjustable pick up adapters
- Double chain hydraulic spotting system
- 3/8" Thick cover plates
- Locking leg with automatic air latch system
- Front frame made from 7/8" thick mast channel.
- Chrome plated pistons
- Fibreglass coated cylinder casings
- Low profile saddle

2MCZC312LPEQ
(105,000 lbs Capacity)
- Two 12 5/8" movable posts (35K Capacity ea.)
- One 12 5/8" fixed and recessed post. (35K Capacity)
- Adjustable pick up adapters
- Double chain hydraulic spotting system
- 3/8" Thick cover plates
- Locking leg with automatic air latch system
- Front frame made from 7/8" thick mast channel.
- Chrome plated pistons
- Fibreglass coated cylinder casings
- Low profile saddle

MCZC310LPEQ
(75,000 lbs Capacity)
- One 10 5/8" movable posts (25K Capacity)
- Dual 10 5/8" fixed and recessed post. (50K Capacity)
- Adjustable pick up adapters
- Double chain hydraulic spotting system
- 3/8" Thick cover plates
- Locking leg with automatic air latch system
- Front frame made from 7/8" thick mast channel.
- Chrome plated pistons
- Fibreglass coated cylinder casings
- Low profile saddle

MCZC210HP
(50,000 lbs Capacity)
- One 10 5/8" movable posts (25K Capacity)
- One 10 5/8" fixed and recessed post. (25K Capacity)
- Adjustable pick up adapters
- Double chain hydraulic spotting system
- 3/8" Thick cover plates
- Locking leg with automatic air latch system
- Front frame made from 7/8" thick mast channel.
- Chrome plated pistons
- Fibreglass coated cylinder casings
- Low profile saddle

MCZC28-210HP
(56,000 lbs Capacity)
- One 10 5/8" movable posts (28K Capacity)
- One 10 5/8" fixed and recessed post. (28K Capacity)
- Adjustable pick up adapters
- Double chain hydraulic spotting system
- 3/8" Thick cover plates
- Locking leg with automatic air latch system
- Front frame made from 7/8" thick mast channel.
- Chrome plated pistons
- Fibreglass coated cylinder casings
- Low profile saddle

MCZC32-210HP
(64,000 lbs Capacity)
- One 10 5/8" movable posts (32K Capacity)
- One 10 5/8" fixed and recessed post. (32K Capacity)
- Adjustable pick up adapters
- Double chain hydraulic spotting system
- 3/8" Thick cover plates
- Locking leg with automatic air latch system
- Front frame made from 7/8" thick mast channel.
- Chrome plated pistons
- Fibreglass coated cylinder casings
- Low profile saddle

MCZC310HP
(75,000 lbs Capacity)
- One 10 5/8" movable posts (25K Capacity)
- Dual 10 5/8" fixed and recessed post. (50K Capacity)
- Adjustable pick up adapters
- Double chain hydraulic spotting system
- 3/8" Thick cover plates
- Locking leg with automatic air latch system
- Front frame made from 7/8" thick mast channel.
- Chrome plated pistons
- Fibreglass coated cylinder casings
- Low profile saddle

2MCZC310HP
(75,000 lbs Capacity)
- Two 10 5/8" movable posts (25K Capacity)
- One 10 5/8" fixed and recessed post. (25K Capacity)
- Adjustable pick up adapters
- Double chain hydraulic spotting system
- 3/8" Thick cover plates
- Locking leg with automatic air latch system
- Front frame made from 7/8" thick mast channel.
- Chrome plated pistons
- Fibreglass coated cylinder casings
- Low profile saddle

MCZC28-310HP
(84,000 lbs Capacity)
- One 10 5/8" movable posts (28K Capacity)
- Dual 10 5/8" fixed and recessed post. (56K Capacity)
- Adjustable pick up adapters
- Double chain hydraulic spotting system
- 3/8" Thick cover plates
- Locking leg with automatic air latch system
- Front frame made from 7/8" thick mast channel.
- Chrome plated pistons
- Fibreglass coated cylinder casings
- Low profile saddle

MCZC32-310HP
(96,000 lbs Capacity)
- One 10 5/8" movable posts (32K Capacity)
- Dual 10 5/8" fixed and recessed post. (64K Capacity)
- Adjustable pick up adapters
- Double chain hydraulic spotting system
- 3/8" Thick cover plates
- Locking leg with automatic air latch system
- Front frame made from 7/8" thick mast channel.
- Chrome plated pistons
- Fibreglass coated cylinder casings
- Low profile saddle

2MCZC28-310HP
(84,000 lbs Capacity)
- Two 10 5/8" movable posts (28K Capacity ea.)
- One 10 5/8" fixed and recessed post. (28K Capacity)
- Adjustable pick up adapters
- Double chain hydraulic spotting system
- 3/8" Thick cover plates
- Locking leg with automatic air latch system
- Front frame made from 7/8" thick mast channel.
- Chrome plated pistons
- Fibreglass coated cylinder casings
- Low profile saddle

2MCZC32-310HP
(96,000 lbs Capacity)
- Two 10 5/8" movable posts (32K Capacity ea.)
- One 10 5/8" fixed and recessed post. (32K Capacity)
- Adjustable pick up adapters
- Double chain hydraulic spotting system
- 3/8" Thick cover plates
- Locking leg with automatic air latch system
- Front frame made from 7/8" thick mast channel.
- Chrome plated pistons
- Fibreglass coated cylinder casings
- Low profile saddle

MCZC1012HP
(72,000 lbs Capacity)
- One 10 5/8" movable posts (32K Capacity ea.)
- One 12 5/8" fixed and recessed post. (40K Capacity)
- Adjustable pick up adapters
- Double chain hydraulic spotting system
- 3/8" Thick cover plates
- Locking leg with automatic air latch system
- Front frame made from 7/8" thick mast channel
- Chrome plated pistons
- Fibreglass coated cylinder casings
- Low profile saddle

PKDT16

Our 2 post/inground hybrid

- High pressure system (available in low)
- 10 5/8" Front & Rear fixed
- 3 stage telescoping arms
- Locking leg with automatic air latch system
- Chrome plated pistons
- Fiberglass coated cylinder casings
- Low profile saddle